Carrier SYSTXCCITW01 Instruction Manual Page 18
- Page / 84
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
10
S Adjust length and routing of each wire to reach each wire entry on the
connector backplate. Strip 1/4--in (6.4 mm) of insulation from each wire.
S Match and connect thermostat wires to proper terminals on control backplate.
d See wiring diagrams in Appendix A.
S Push any excess wire into the wall. Seal hole in wall to prevent any air leaks.
Leaks can affect operation.
S Attach Infinity Control to the mounting plastic by lining up the plastic guides
on the back of the control with the opening on the mounting plastic and push
on.
S Perform installation of all other system equipment (i.e. dampers, humidifier,
ventilator, UV lights, etc.).
S Turn on power to equipment.
4.4.1. Shielded Wire
If the thermostat wiring will be located near or in parallel with high voltage wiring,
radio, TV or Ethernet wiring, then four conductor, twisted --pair, shielded cable can
be used to reduce or eliminate potential interference. The shield wire should be
connected to the C terminal, or ground, at the indoor unit. The shield wire should
NOT be connected to any terminal at the user interface. Connecting the shield to
ground at both ends can cause current loops in the shield, reducing shield
effectiveness.
Connect one pair of the two--pair (minimum) cable to the A and B communication
terminals, and another pair to the C and D terminals at both ends of the cable. The
shield wire should ONLY be connected at the indoor equipment ground or C
terminal. Note that some outdoor units only require the A and B connections. See
the outdoor unit installation instructions for more information.
- Installation Instructions 1
- TABLE OF CONTENTS 3
- TABLE OF CONTENTS (cont.) 4
- 1. Safety Considerations 9
- 2. Introduction 9
- 3. Quick Start 10
- 3.1. Set Time and Date 10
- 3.2. Set Dealer Information 11
- 4. Installation 12
- 4.1. Over view 12
- 4.2. Check Equipment 12
- 4.3. Location 13
- 4.3.1. Wall Control 13
- 4.3.2. Remote Room Sensors 14
- 4.4. Wiring Considerations 15
- 4.4.1. Shielded Wire 18
- 4.5. Mounting 19
- 4.5.1. Decorati ve Backplate 20
- 4.6. Humidifier Connections 21
- 4.6.1. Bypass Humidifie r 21
- 5. Commissioning 22
- 5.7. Filter Type Selection 27
- 5.8. Humidifier Installation 27
- 5.10. Equipment Summary 27
- 5.11. Static Pressure Check 28
- 6. Service Menu 30
- 6.1. Equipment Summary 30
- 6.2. Installation 31
- 6.3. Set up 32
- 6.3.1. Thermostat 33
- 6.3.1.1. Auto Mode set up 33
- 6.3.1.2. Heat/Cool Deadband 34
- 6.3.1.3. Offsets 34
- 6.3.1.5. Scheduling Enable 34
- 6.3.2. Fan Coil 35
- 6.3.2.1. Airflow 36
- 6.3.2.2. Altitude 36
- 6.3.2.4. Fan Coil G--Terminal 37
- 6.3.3. Furnace 38
- 6.3.3.1. Furnace Airflow 38
- 6.3.3.2. AC/HP Air Flow 39
- 6.3.3.3. Furnace Staging 40
- 6.3.3.5. Furnace Off Delay 40
- 6.3.3.6. Altitude 41
- 6.3.3.8. Furnace G Terminal 41
- 6.3.4. AC/Heat Pump 42
- 6.3.4.1. Cooling Lockout 43
- 6.3.4.2. Defrost Interval 43
- 6.3.4.3. Low Ambient Cooling 44
- 6.3.4.4. Quiet Shift 44
- 6.3.4.5. AC/Heat Pump RPM Max 44
- 6.3.4.6. Defrost Fan Delay 44
- 6.3.4.7. Brownout Disable 45
- 6.3.4.8. Energy Efficiency 45
- 6.3.5. Heat Source Lockout 45
- 6.3.6. Zoning (If Applicable) 46
- 6.3.6.1. Zoning Disable 47
- 6.3.6.2. Zone Offsets 47
- 6.3.6.3. Zone Airflow Limits 47
- 6.3.6.4. Duct Assessment Time 48
- 6.3.7. Accessories 48
- 6.3.7.1. Filter 49
- 6.3.7.2. Humidifier 49
- 6.3.7.3. Ultraviolet Lights 50
- 6.3.7.4. Ventilator 50
- 6.3.8. Utility Curtailment 50
- 6.3.9. Hydronic Airflow 51
- 6.4. Check out 52
- 6.4.1. Electric Heat 52
- 6.4.2. Furnace 53
- 6.4.3. Hydronic 53
- 6.4.4. Air Conditioning 53
- 6.4.5. Heat Pump Heating 54
- 6.4.6. Heat Pump Cooling 55
- 6.4.7. Humidifier 55
- 6.4.8. Ventilator 56
- 6.4.9. Zoning (If Applicable) 56
- 6.4.9.1. Airflow Limits 56
- 6.4.9.2. Damper/Sensor Check 56
- 6.4.9.3. Zone Duct Assessment 57
- 6.4.9.4. Sensor Type 57
- 6.5. Service Information 57
- 6.5.1. Fan Coil Status 58
- 6.5.2. Furnace Status 58
- 6.5.3. AC Status 59
- 6.5.4. Heat Pump Status 59
- 6.5.5. Zoning Status 60
- 6.5.6. Last 10 System Faults 60
- 6.5.7. Run/Fault History 61
- 6.5.8. Model/Serial Numbers 62
- 6.5.9. Service Phone Number 62
- 6.6. Refrige rant Charging 63
- 6.6.1. Charging 63
- 6.6.2. Pump down 64
- 6.6.3. Evacuation 65
- 6.7. Dealer Logo 65
- User Interface 73
- Communicating 73
- AC or HP* 73
- Variable-Speed 73
- Furnace/ Fan Coil 73
- Furnace/Fan Coil 74
- Fan Coil 75
- Humidifier 76
- Connection 76
- (Optional) 76
- 1-Stage AC 77
- 1-Spd. HP 78
- FE Fan Coil or 79
- Variable Speed Furnace 79
- Catalog No: SYSTXCCITW---06SI 84
Related products and manuals for Recording Equipment Carrier SYSTXCCITW01
(80 pages)© 2020, manymanuals.com. All rights reserved. | 0.091 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals