Carrier 58CTA/CTX User Manual download pdf (Page 3)

Table1–Dimensions

FURNACE SIZE

CABINET

WIDTH

IN (mm)

SUPPLY ---AIR

WIDTH

IN (mm)

RETURN---AIR

WIDTH

IN (mm)

C.L. TOP AND

BOTTOM FLUE

COLLAR

IN (mm)

FLUE

COLLAR*

IN (mm)

SHIP WT

LB (KG)

FILT ER

MEDIA

CABINET

IN (mm)

045---08/024045 14--- 3/16 (360) 12--- 9/16 (319) 12---11/16 (322) 9--- 5/16 (237) 4 (102) 104 (47) 16 (406)

045---12/036045 14--- 3/16 (360) 12--- 9/16 (319) 12---11/16 (322) 9--- 5/16 (237) 4 (102) 107 (48) 16 (406)

070---08/024070 14--- 3/16 (360) 12--- 9/16 (319) 12---11/16 (322) 9--- 5/16 (237) 4 (102) 111 (50) 16 (406)

070---12/036070 14--- 3/16 (360) 12--- 9/16 (319) 12---11/16 (322) 9--- 5/16 (237) 4 (102) 115 (52) 16 (406)

070---16/048070 17--- 1/2 (445) 15--- 7/8 (403) 16 (406) 11--- 9/16 (294) 4 (102) 126 (57) 16 (406)

090---14/042090 17--- 1/2 (445) 15--- 7/8 (403) 16 (406) 11--- 9/16 (294) 4 (102) 127 (58) 16 (406)

090---16/048090 21 (533) 19--- 3/8 (492) 19--- 1/2 (495) 13--- 5/16 (338) 4 (102) 140 (64) 20 (508)

090---20/060090 21 (533) 19--- 3/8 (492) 19--- 1/2 (495) 13--- 5/16 (338) 4 (102) 146 (66) 20 (508)

110---12/036110 17--- 1/2 (445) 15--- 7/8 (403) 16 (406) 11--- 9/16 (294) 4 (102) 135 (61) 16 (406)

110---16/048110 21 (533) 19--- 3/8 (492) 19--- 1/2 (495) 13--- 5/16 (338) 4 (102) 146 (66) 20 (508)

110---22/066110 21 (533) 19--- 3/8 (492) 19--- 1/2 (495) 13--- 5/16 (338) 4 (102) 152 (69) 20 (508)

135---16/048135 21 (533) 19--- 3/8 (492) 19--- 1/2 (495) 13--- 5/16 (338) 4 (102) 149 (68) 20 (508)

135---22/066135 24--- 1/2 (622) 22--- 7/8 (581) 23 (584) 15--- 1/16 (383) 4 (102) 163 (74) 24 (610)

155---20/060155 24--- 1/2 (622) 22--- 7/8 (581) 23 (584) 15--- 1/16 (383) 4 (102) 170 (77) 24 (610)

* 5 ---in. or 6 ---in. (127 or 152 mm) vent connector may be required in some cases.

{ 135 and 155 size fur naces require 5---in. (127 mm) or larger vents. U se a 4 to 5 or 4 to 6---in. (102 to 127 or 102 to 152 mm) vent adapter between furna ce and

vent connector.

product and property damage. NOTE is used to highlight

suggestions which will result in enhanced installation, reliability,

or operation.

1. Use only with type of gas approved for this furnace. Refer

to the furnace rating plate 2. Install this furnace only in a

2. Install this furnace only in a location and position as spe-

cified in the “Location” section of these instructions.

3. Provide adequate combustion and ventilation air to the

furnace space as specified in “Air for Combustion and

Ventilation” section.

4. Combustion products must be discharged outdoors. Con-

nect this furnace to an approved vent system only, as spe-

cified in the “Venting” section of these instructions.

5. Never test for gas leaks with an open flame. Use a com-

mercially available soap solution made specifically for the

detection of leaks to check all connections, as specified in

the “Gas Piping” section.

6. Always install furnace to operate within the furnace’s in-

tended temperature--rise range with a duct system which

has an external static pressure within the allowable range,

as specified in the “Start--Up, Adjustments, and Safety

Check” section. See furnace rating plate.

7. When a furnace is installed so that supply ducts carry air

circulated by the furnace to areas outside the space con-

taining the furnace, the return air shall also be handled by

duct(s) sealed to the furnace casing and terminating out-

side the space containing the furnace. See “Air Ducts” sec-

tion.

8. A gas--fired furnace for installation in a residential garage

must be installed as specified in the warning box in the

“Location” section.

9. The furnace may be used for construction heat provided

that the furnace installation and operation complies with

the first CAUTION in the LOCATION section of these in-

structions.

10. These Multipoise Gas--Fired Furnaces are CSA (formerly

A.G.A. and C.G.A.) design--certified for use with natural

and propane gases (see furnace rating plate) and for install-

ation in alcoves, attics, basements, closets, utility rooms,

crawlspaces, and garages. The furnace is factory--shipped

for use with natural gas. A CSA (A.G.A. and C.G.A.) lis-

ted accessory gas conversion kit is required to convert fur-

nace for use with propane gas.

11. See Fig. 2 for required clearances to combustible construc-

tion.

12. Maintain a 1--in. (25 mm) clearance from combustible ma-

terials to supply air ductwork for a distance of 36 inches

(914 mm) horizontally from the furnace. See NFPA 90B

or local code for further requirements.

13. These furnaces SHALL NOT be installed directly on car-

peting, tile, or any other combustible material other than

wood flooring. In downflow installations, factory access-

ory floor base MUST be used when installed on combust-

ible materials and wood flooring. Special base is not re-

quired when this furnace is installed on manufacturer’s

Coil Assembly Part No. CAR, CAP, CNRV, CNPV or

when Coil Box Part No. KCAKC is used. See Fig. 2 for

clearance to combustible construction information.

INTRODUCTION

The Series 130/D 4--way multipoise Category I fan--assisted

furnace is CSA (formerly A.G.A.. and C.G.A.) design--certified.

A Category I fan--assisted furnace is an appliance equipped with

an integral mechanical means to either draw or force products of

combustion through the combustion chamber and/or heat

exchanger. The furnace is factory--shipped for use with natural

gas. This furnace is not approved for installation in mobile

homes, recreational vehicles, or outdoors.

These furnaces shall not be installed directly on carpeting, tile, or

any other combustible material other than wood flooring. For

downflow installations, a factory accessory floor base must be

used when installed on combustible materials and wood flooring.

This special base is not required when this furnace is installed on

the manufacturer’s coil assembly, or when the manufacturer’s coil

box is used. See Fig. 2 for clearance to combustible material

information.

This furnace is designed for minimum continuous return--air

temperature of 60_F(16_C) db or intermittent operation down to

55_F(13_C) db such as when used with a night setback

thermostat. Return--air temperature must not exceed 80_F(27_C)

db. Failure to follow these return--air temperature limits may

affect reliability of heat exchangers, motors, and controls. (See

Fig. 3.)

For accessory installation details, refer to the applicable

instruction literature.

NOTE: Remove all shipping brackets and materials before

operating the furnace.

58CT

1 2 3 4 5 6 7 8 ... 55 56

Comments to this Manuals

No comments

Carrier 58CTA/CTX User Manual Page 3

Comments to this Manuals

Related products and manuals for Cookers Carrier 58CTA/CTX