Carrier JWL-1221VS Operations Instructions

Operating Instructions and Parts Manual 12x21-inch EVS Woodworking Lathe Model JWL-1221VS WALTER MEIER (Manufacturing) Inc. 427 New Sanford

10 Figure 5 To remove faceplate: 6. Make sure both set screws have been backed out. 7. Engage spindle lock (A, Figure 5). 8. Place wrench (C) over

118.0 Electrical connections The JWL-1221VS JET lathe is rated for 115 volt operation. It is supplied with a plug designed for use on a circuit with

129.0 Adjustments Make sure all levers and locking handles are tightened before operating the lathe. 9.1 Tool rest Referring to Figure 10: The t

132. Relieve belt tension by pulling handle (F, Figure 14) while pushing up lever (G). 3. Move belt to desired pulley set. Make sure belt is proper

1411.0 Operation The information which follows is general in nature and is not intended to be a complete course in wood turning. Nothing can replace

1511.3 Spindle Turning Spindle turning takes place between the centers of the lathe. It requires a spur or drive center in the headstock, and a live

16 Figure 21 11. Rotate workpiece by hand to check for proper clearance. 12. Start lathe at lowest speed and bring it up to the appropriate RPM for t

174. With the bevel parallel to the right side of the cut, raise the handle and push the tool in to the desired depth, as shown in Figure 24. Figur

18FaceplateorChuck?While faceplates are the simplest, most reliable method of holding a block of wood for turning, chucks can also be used. As th

19(NOTE: If you plan to use a chuck, turn a tenon of the appropriate length and diameter to fit your chuck.) 9. Stop the lathe, remove workpiece and

21.0 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of ou

20Bearings are permanently lubricated and sealed. They do not require further lubrication. 12.2 Motor Brushes Referring to Figure 28: Periodically i

21 Figure 32 10. Remove belt through lower access door. 11. Reverse above procedure to install belt and re-position spindle. NOTE: Make sure to in

2214.0 Optional accessories These accessory items, purchased separately, can enhance the functionality of your lathe. Contact your dealer to order,

2315.0 Troubleshooting the JWL-1221VS Lathe Table 3 Trouble Probable Cause Remedy Motor fails to develop full power Power line overloaded Correct

24Trouble Probable Cause Remedy E7 shown on digital readout Motor sensor not working Check connectors of motor sensor cord to switch box Readjust s

2516.1.1 Bed Assembly – Exploded View

2616.1.2 Bed Assembly – Parts List IndexNo PartNo Description Size Qty1 ... JWL1221VS-201 ... Tool Caddy ...

27IndexNo PartNo Description Size Qty57 ... JWL1221VS-257 ... Bracket...

2816.2.1 Headstock Assembly – Exploded View

2916.2.2 Headstock Assembly – Parts List IndexNo PartNo Description Size Qty ... JEL1221VS-HA ... Headstock Assembly (in

32.0 Table of contents Section Page 1.0 Warranty and Service ...

3016.3.1 Controller Assembly – Exploded View 16.3.2 Controller Assembly – Parts List IndexNo PartNo Description Size Qty ...

3117.0 Electrical Connections NLM-M+MOTORWHITEBLACKGREENGNDPRINTED CIRCUIT BOARDS-S M-S VR LI-SW V

32 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jetto

4 3.0 Safety warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the wa

525. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do not use your hands. 26. Do not stand on the m

65.0 Features and nomenclature – JWL-1221VS lathe Figure 1 1. Spindle handwheel 2. Index pin 3. Speed chart 4. Upper pulley access door 5. Hea

76.0 Specifications – JWL-1221VS lathe Model number ...

86.1 Hole pattern – JWL-1221VS lathe Figure 2 Clearance hole spacing for mounting lathe

97.0 Setup and assembly Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent.