Carrier AQUASNAP 30RH User Manual

30RA/RY - 30RH/RYH SeriesPRO-DIALOG ControlOperation and maintenance instructionsAQUASNAP

10CHANGING THE OPERATING TYPEBUTTON ACTIONContinually press the operating typeselection button for more than 4 seconds.Hold down the Start/Stop button

114.3 - Menus4.3.1 - Selecting a menuThe MENU button authorises you to select a menu from the 10main menus that are available. Each time you press thi

120011 6.01 6.01 5.91 5.81 5.71 5.7MODIFYING THE VALUE OF A PARAMETEROPERATION PRESS BUTTON MENU LED ITEM NUMBER ITEM VALUE2-DIGIT DISPLAY 4-DIGIT DIS

13STATUS TEMPERATURES PRESSURES SETPOINTS INPUTS OUTPUTS CONFIGURATION ALARMS ALARMS HISTORYALARMSUSER[USEr]SERVICE[SErviCE]FACTORY[FACtorY]RUNTIME 1[

14MENUMenu tree structureLegend* Displayed if the configuration requires it** Displayed if the alarm exists- Not in useITEM012345678910111213141516STA

15INFORMATION MENU (3)ITEM FORMAT UNITS0±nn.n °CLOFF -L-On -L-Sc -CCn -rEM -MASt -OFF -rEADY -dELAY -StOPPing -running -triPout -OvErridE -dEFrOSt -OC

16DESCRIPTIONThe delay at start-up operates after the unit has been switched on. If the delay has not expired, the mode is active.The delay is configu

17SETPOINTS MENU [2]ITEM FORMAT UNITS RANGE0 ±nn.n °C See table below1 ±nn.n °C See table below2 nnn °C See table below3 [1] nnn °C See table below4 [

18INPUTS MENU [2]ITEM FORMAT UNITS0 oPEn/CLoS -1 [1] oPEn/CLoS -2 oPEn/CLoS -3 oPEn/CLoS -4 [1] oPEn/CLoS -5 [1] oPEn/CLoS -6 [1] oPEn/CLoS -7 oPEn/CL

194.3.10 - Description of the Outputs/Tests menu4.3.10.1 - GeneralThis menu displays the status of the controller outputs. Moreo-ver, when the machine

2TABLE OF CONTENTS1 - SAFETY CONSIDERATIONS...

20OUTPUTS STATUS & TESTS MENU [2] [3] continuedITEM FORMAT UNITS11 [1] nnntESt %12 [1] nnntESt %13 [1] b1b2tESt14 [1] b1b2b3b4tESt15 [1] YES -no -

21The table below describes the different sequences of theautomatic test.TEST NUMBER012345, 67, 8, 910, 1112, 13, 1415, 16, 171819, 20, 21222324252627

22The table below describes the faults that can be displayedduring the automatic test.TEST FAULT1234567891011, 12, 13; 14, 1516, 17, 18, 19, 202122, 2

23SUB-MENU USER CONFIGURATION* only displayed if configuration requires.NOTE: The items in brackets show what is displayed on theuser interface.SCHED

244.3.11.3 - Description of the User 1 Configuration sub-menu1 This item shall be masked when not used.2 Access to menu is read/write.USER 1 CONFIGURA

254.3.11.4 - Description of the User 2 Configuration sub-menuThis menu is only accessible if the unit is equipped with anoptional CCN/clock board4.3.1

26PERIOD X CONFIGURATION SUB-MENUS (X = 1 TO 8)ITEM # FORMAT COMMENTS0 Period X Menu Indicates the period (X) you are going to configure.When selected

27BROADCAST CONFIGURATION SUB-MENUITEM # FORMAT COMMENTS0 broAdCASt MEnu When selected this item authorises a return to the main menu.1 YES/no Determi

28ITEM #0 [1]1 [1]2 [1]3 [1]4 [1]5 [1]FORMAT X ALArMrESEt ALArM1 to 551 to 551 to 551 to 551 to 55COMMENTSX alarms are activeReset of alarms is reques

295 - PRO-DIALOG PLUS CONTROL OPERATION5.1 - Start/stop controlThe table below summarises the unit control type and stop orgo status with regard to th

3GENERAL LEGENDEach of the following drawings is replaced in the whole document by the corresponding explanation:Start/stop buttonReturn keyDown arrow

30CHIL_S_S------Disable----Disable------Enable----EnableREMOTESTART/STOPCONTACT----Off----Off-----On coolingOn heatingOn auto--On coolingOn heatingOn

315.3 - Evaporator water pump controlThe unit can control one or two evaporator water pumps. Theevaporator water pump is turned on when this option is

32The following table summarises the possible selectionsdepending on the control types (local, remote or CCN) and thefollowing parameters:- Setpoint s

335.6.2 - ResetReset means that the active setpoint is modified so that lessmachine capacity is required (in cooling mode, the setpoint isincreased, i

345.11 - Defrost functionDefrost is activated, when the unit is in heating mode, in orderto reduce frost build-up on the air heat exchanger. The defro

35ALARMCODE123567910111213141516171821222324ALARM NAMECompressor A1 failureCompressor A2 failureCompressor A3 failureCompressor B1 failureCompressor B

Order No. 13048-76, 07.2000. Supersedes order No. 13048-76, 01.2000 Manufactured by: Carrier s.a., Montluel, France.Manufacturer reserves the right to

41 - SAFETY CONSIDERATIONS1.1 - GeneralInstallation, start-up and servicing of equipment can behazardous if certain factors particular to the installa

53 - HARDWARE DESCRIPTION3.1 - GeneralFigure 13.2 - Electrical supply to boardsAll boards, except the PD-RCPM board, are supplied from acommon 24 V a.

63.6 - Connections at the user's terminal block3.6.1 - General descriptionThe contacts below are available at the user's terminal block onth

7DescriptionAlarm relay outputcircuit AAlarm relay outputcircuit BBoiler relay outputContact 1:start/stop/heat/coolContact 2:start/stop/heat/coolConta

83.6.2 - Volt-free contact on/off/cooling/heating withoutmultiplexingIf the automatic heating/cooling changeover function is notselected (see sections

9MAIN INTERFACEBUTTON NAME DESCRIPTIONMenu Permits the selection of a main menu. Each main menu is represented by an icon. The icon is lit if active.U