Carrier 58WAV Instruction Manual download pdf (Page 2)

The ability to properly perform maintenance on this equip-

ment requires certain expertise, mechanical skills, tools, and

equipment. If you do not possess these, do not attempt to

perform any maintenance on this equipment other than those

procedures recommended in the User’s Manual. FAILURE

TO FOLLOW THIS WARNING COULD RESULT IN

POSSIBLE DAMAGE TO THIS EQUIPMENT, SERIOUS

PERSONAL INJURY, OR DEATH.

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

PROCEDURE

Electrostatic discharge can affect electronic components.

Take precautions during furnace installation and servicing to

protect the furnace electronic control. Precautions will pre-

vent electrostatic discharges from personnel and hand tools

which are held during the procedure. These precautions will

help to avoid exposing the control to electrostatic discharge

by putting the furnace, the control, and the person at the same

electrostatic potential.

1. Disconnect all power to the furnace. DO NOT TOUCH THE

CONTROL OR ANY WIRE CONNECTED TO THE CON-

TROL PRIOR TO DISCHARGING YOUR BODY’S ELEC-

TROSTATIC CHARGE TO GROUND.

2. Firmly touch a clean, unpainted, metal surface of the furnace

chassis which is close to the control. Tools held in a person’s

hand during grounding will be satisfactorily discharged.

3. After touching the chassis you may proceed to service the

control or connecting wires as long as you do nothing that

recharges your body with static electricity (for example; DO

NOT move or shuffle your feet, DO NOT touch ungrounded

objects, etc.).

4. If you touch ungrounded objects (recharge your body with

static electricity), firmly touch furnace again before touching

control or wires.

5. Use this procedure for installed and uninstalled (ungrounded)

furnaces.

6. Before removing a new control from its container, discharge

your body’s electrostatic charge to ground to protect the

control from damage. If the control is to be installed in a

furnace, follow items 1 through 5 before bringing the control

or yourself into contact with the furnace. Put all used AND

new controls into containers before touching ungrounded

objects.

7. An ESD service kit (available from commercial sources) may

also be used to prevent ESD damage.

CARE AND MAINTENANCE

For continuing high performance and to minimize possible equip-

ment failure, it is essential that periodic maintenance be performed

on this equipment. Consult your local dealer as to the proper

frequency of maintenance and the availability of a maintenance

contract.

Never store anything on, near, or in contact with the furnace,

such as:

1. Spray or aerosol cans, rags, brooms, dust mops, vacuum

cleaners, or other cleaning tools.

2. Soap powders, bleaches, waxes or other cleaning com-

pounds, plastic or plastic containers, gasoline, kerosene,

cigarette lighter fluid, dry cleaning fluids, or other volatile

fluids.

3. Paint thinners and other painting compounds, paper bags

or other paper products.

A failure to follow this warning could result in corrosion of

the heat exchanger, fire, personal injury, or death.

Turn off the gas and electrical supplies to the unit before

performing any maintenance or service. Follow the operating

instructions on label attached to furnace. A failure to follow

this warning could result in personal injury.

The minimum maintenance that should be performed on this

equipment is as follows:

1. Check and clean air filter each month or more frequently if

required. Replace if torn.

2. Check blower motor and wheel for cleanliness each heating

and cooling season. Clean and lubricate as necessary.

3. Check electrical connections for tightness and controls for

proper operation each heating season. Service as necessary.

As with any mechanical equipment, personal injury can result

from sharp metal edges, etc., therefore, be careful when

removing parts.

AIR FILTER ARRANGEMENT

The air filter arrangement may vary depending on the application.

Refer to Table 1 or 2 for filter size information.

Table 1—Filter Size Information for

Downflow/Horizontal Furnaces (In.)

FURNACE

CASING WIDTH

FILTER QUANTITY

AND SIZE

FILTER

TYPE

14-3/16 (2) 14 X 20 X 1 Cleanable

17-1/2 (2) 14 X 20 X 1 Cleanable

21 (2) 16 X 20 X 1 Cleanable

24-1/2 (2) 16 X 20 X 1 Cleanable

Table 2—Filter Size Information for Upflow

Furnaces (In.)

FURNACE

CASING WIDTH

FILTER QUANTITY AND SIZE

FILTER

TYPE

Side Return Bottom Return

14-3/16 (1) 16 X 25 X 1* (1) 14 X 25 X 1 Cleanable

17-1/2 (1) 16 X 25 X 1* (1) 16 X 25 X 1 Cleanable

21 (1) 16 X 25 X 1 (1) 20 X 25 X 1* Cleanable

24-1/2 (2) 16 X 25 X 1* (1) 24 X 25 X 1 Cleanable

* Factory-provided with the furnace. Filters may be field modified as required

by cutting and folding the frame as indicated on the filter.

1 2 3 4 5 6 7 ... 11 12

Comments to this Manuals

No comments

Carrier 58WAV Instruction Manual Page 2

Comments to this Manuals

Related products and manuals for Fireplaces Carrier 58WAV